Napco Security Technologies GEM-DXRP2 Uživatelský manuál Strana 18
- Strana / 36
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
18
Display Telephone List? (OPTIONAL) (For GEM-P9600/3200 panels only). (Phone Numbers
Programmed?
YES NO). The panel can dial any of four programmed telephone numbers.
Select Telephone #1-4 using the NEXT and PRIOR buttons. Press
D, then pick up the phone
to automatically dial the displayed number.
Display System Troubles? (For GEM-P9600/3200 panels only). Displays a 2-digit error code
(EXX-NN) representing the problem (XX) detected in the system, followed by 2 digits (NN) identi-
fying the problem zone, keypad, module, etc. (See SYSTEM TROUBLE ERROR CODES for a
description of these codes). Use NEXT(
E) and PRIOR (F) to scroll system troubles.
Display Fire Alarms? (For GEM-P9600/3200 panels only). Displays alarms that have occurred on
the Fire Zone(s). Press the NEXT and PRIOR Buttons to scroll zones.
Display Fire Troubles? (For GEM-P9600/3200 panels only). Displays trouble conditions that
have been detected on the Fire Zone(s). Use NEXT(E) and PRIOR (F) to scroll fire
troubles.
Activate Overview? (OPTIONAL) (For GEM-P9600/3200 panels only). (Overview programmed
for user? YES NO). In a partitioned system, this mode displays the status of Areas 1 and
2 simultaneously. (The “READY1” display will be replace by the “OV(--)” display shown at left).
For each area: “R” = Area Ready; “z” = Zone Fault; “A” = Area Armed; “B” Burglary Zone in
Alarm; “F” Fire Zone in Alarm; “T” = Fire Trouble; "c” = Check Trouble; Area in Function-Display
Mode.
In this mode, all areas (except the area that you are in) may be armed by pressing 9. G,
then entering a valid User Code. (The User Code must be valid in all areas). Similarly, all areas
may be disarmed by pressing
0, G, then entering a valid User Code. To revert to nor-
mal keypad operation, enter a valid code, press
A repeatedly until "TrnOff O View" appears,
then press the YES (E) button.
KEYPAD FUNCTIONS
AC ON
DspTel/List/
Yes/No
AC ON
DspSys/Trbl/
Yes/No
reset FIRE ALARM
AC ON
DspFir/Alarm/
Yes/No
TROUBLE
AC ON
DspFir/Trbl/
Yes/No
AC ON
TurnOn/O view
Yes/No
AC ON
OV(RZ)
- OPERATING GUIDE for your 1
- INTRODUCTION 2
- TABLE OF CONTENTS 3
- G button to signal an 5
- 7 and the G 5
- 8 and the G 5
- 9 and the G 5
- ZONES FAULTED 6
- 02 BACK DOOR 6
- BYPASSED 6
- 02 BACK DOOR 6
- C, then arm the panel. A 3 7
- C and the system trou 7
- Area Arming (Optional) 8
- YES NO) 9
- Instant Protection 10
- Disarming the System 11
- To silence an audible alarm: 11
- 991234J 12
- FIRE PROTECTION 13
- KEYPAD FUNCTIONS 17
- CENTRAL STATION MONITORING 22
- ADVANCED FEATURES 23
- PROGRAMMING (OPTIONAL) 25
- User 01 26
- KEYPAD MESSAGES 28
- GLOSSARY 32
- SYSTEM TROUBLE ERROR CODES 35
- NAPCO LIMITED WARRANTY 36
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Napco Security Technologies GEM-DXRP2
Bezpečnostní systémy pro řízení přístupu Napco Security Technologies XP-400 Uživatelský manuál
(28 stránky)
(28 stránky)
Bezpečnostní systémy pro řízení přístupu Napco Security Technologies GEM-DXK3 Uživatelský manuál
(32 stránky)
(32 stránky)
Bezpečnostní systémy pro řízení přístupu Napco Security Technologies GEM-K1CA Uživatelský manuál
(40 stránky)
(40 stránky)
Sony NEX-VG10 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla odtwarzacze CD Sony NEX-VG10.
Dostarczamy pdf podręczników Sony NEX-VG10 do pobrania za darmo według typów dokumentów:
Komentáře k této Příručce